The Cisco Meraki Cloud Dashboard: Managing the Whole Network From One Console
16 November 2026Choosing a Network Consultant for Your Organization: The Questions to Ask Before You Open Your Network
16 November 2026A warehouse is not a big office. HPE Aruba Networking sums up what makes it hard: high ceilings, metal shelving,
inventory levels that change, and demanding environmental conditions
(warehouse guide). There
are fewer devices per access point than in an office, and each access point often covers 900 to 2,500 m², but coverage
has to follow the barcode scanners, tablets, forklifts and phones wherever they go.
1. The racking, and what it holds
For Aruba, shelving is a significant barrier to the signal, and metal racks full of inventory weaken it a great deal.
An access point above an aisle covers that aisle well; the neighbouring aisles get less. What is stored matters too: in
its design model, Aruba counts 3 dB of loss per metre of racking for dry goods, and 10 dB for liquids. And both the
layout and the inventory can change often: Aruba counts seasonal variations among what to look at before designing
the network.
In practice, Aruba recommends at least one access point per aisle, staggered from one aisle to the next. Skipping
every other aisle can leave real gaps, and no backup if an access point fails (same source).
2. Ceiling height
The higher the access point, the more signal is lost on the way. Above 15 metres of ceiling, Aruba advises directional
antennas, which send the signal toward the floor, and prefers ceiling mounting to wall mounting (warehouse guide).
Cisco Meraki gives a general rule along the same lines: integrated antennas below about 3 metres, external downtilt
antennas between 3 and 8 metres, directional antennas if the access point cannot be mounted below 8 metres
(high density deployments).
Cold rooms and freezers add their share: extreme cold, insulated walls and sealed doors change how the signal travels,
and Aruba recommends outdoor-rated access points for many warehouses (warehouse guide).
3. Devices on the move
A scanner moves from one access point to the next as it rolls down the aisle, and the device decides when to switch
(roaming technologies).
Zebra, which makes scanners of this kind, says its devices look for another access point, for example when theirs
drops below -65 dBm, and strongly recommends 802.11r fast transition
(Zebra’s recommendations).
Meraki, for its part, warns that some older devices may not connect to an 802.11r network, so take stock of the
devices before turning it on (roaming technologies).
For coverage, Aruba aims for -65 dBm from the primary access point (-60 dBm for voice) and -72 dBm from the backup one
(warehouse guide). These are its thresholds, not a universal rule, and Cisco Meraki asks for coverage to be surveyed
for the weakest devices in the fleet
(site surveys).
4. The bands: 2.4, 5 and 6 GHz
The 2.4 GHz band has only three channels that do not overlap (1, 6 and 11); it travels further and penetrates better
than 5 GHz in general, which offers more channels, some of which must avoid radar
(channel planning).
6 GHz requires WPA3 (or, for an open network, Enhanced Open), WPA2 is not allowed there, and every device has to
support it
(Wi-Fi 6E). In
Canada, a low-power 6 GHz access point is for indoor use only, in a place completely enclosed by walls and a ceiling
(RSS-248).
An open dock or a yard is not.
5. Measure before you install
Aruba describes three phases: a predictive model built from the floor plans (the racking, its height, the ceiling
height, the list of devices), then an onsite survey, aisle by aisle, with a temporary access point on a mast, then a
written design that stays on file (warehouse guide). Our article on
Wi-Fi site surveys explains the survey itself.
6. Security: warehouse devices on their own
The Canadian Centre for Cyber Security recommends WPA3 for every new deployment, one VLAN per network name, a separate
secure network for printers and connected devices that cannot sign in like an employee, and turning off WPS
(ITSP.80.002). It adds that VLANs alone are not a security
solution for separating networks: traffic from one zone to another goes through a controlled point, such as a
firewall. In a factory, separating production systems from IT is paramount
(ITSM.10.092).
Drivers and visitors get their own network, as our article on
guest Wi-Fi describes. And a fixed machine is wired when
possible: the Canadian Centre points out that a business network should not rely on Wi-Fi alone
(ITSAP.80.009).
Frequently asked questions
How many Wi-Fi access points does a warehouse need?
Aruba says an access point often covers 900 to 2,500 m² in a warehouse, and recommends at least one per aisle. The
real number comes from the onsite survey.
Are directional antennas needed in a warehouse?
Aruba advises them above 15 metres of ceiling, to send the signal toward the floor. Cisco Meraki advises them when the
access point cannot be mounted below 8 metres.
Can 6 GHz be used in a warehouse?
It requires WPA3 (or Enhanced Open for an open network) and devices that support it. In Canada, a low-power 6 GHz access point is for indoor use only, in a
place completely enclosed by walls and a ceiling.
To go further
Our Aruba Wi-Fi and Cisco Meraki
pages present the access points we install, and our
Dell servers and switches page, the switches.
What now?
To adjust access points and segments as your space changes, MPJM’s
monthly block of hours sets hours aside each month. To start, the
free network analysis measures coverage, the switches and who can connect
to what. It is offered to organizations with 40 or more employees.
P.S. Sixteen questions, eight domains, a clear picture of your strengths and blind spots: start the assessment.
